Share this content on Facebook!
18 Sep 2015
The target here is mainly on bathroom installation, particularly on shower or bathtub installation, bathtub enclosure and bathtub surround installation. Before anything else, let us look at some common errors and recommended guidelines a part of bathroom installation. bathroom fitters glasgow


Most Common Mistakes and Guidelines for lavatory Installation

There are a number of common errors observed from most of the bathroom installation. Listed here is a list of those errors:

• Ignoring or violating local code restrictions
• Employing pipes which are too small
• Attaching copper to galvanized without getting a brass or dielectric fitting backward and forward
• Not considering Teflon tape or pipe compound especially at threaded joints
• Not installing an air gap filling for fixtures
• Not properly aligning tubing into fitting or stop valves
• Cutting supply stub outs short to install the shutoff valves onto following the finished wall is in place
• Not leveling fixtures when setting them up

Now, after knowing those errors, It is best for you to know a number of the standards developed by government entities for those who are thinking of your bathrooms improvement. Note that these standards are highly applicable regardless if you are planning of designing a bath room for wheelchair or just to make the room much more comfortable and functional for anybody with limited mobility. Here are several of the recommended guidelines:
bathroom installations glasgow


Entrances

You start with your entrance in the room, I know that you would like to make sure that the door is at least 32 inches wide. Should the doorway is located off a hallway plus you've got a wheelchair that have to turn from the hall to the doorway, then the door width have to be adjusted to about 36 inches. Also if possible, avoid placing threshold in the doorway. However, in case a particular threshold is required, you try to choose an appartment one that is no more than ¼ inch high, or maybe one that is beveled on both sides with out greater than ¾ inch high. Degrees of training a member in the family with limited hand strength, a standard door knob can be extremely difficult to grip. So, what's commonly advised is always to select a lever handle, rather than knob. The height on this handles must be at 48 inches or fewer above the floor.

Bathroom Fixtures

Rather than conventional toilet which is about 14 to fifteen inches above the floor, you can use accessible toilets which are designed and developed so the seat is between 17 to 19 inches over the floor. For the sink, you might want to make sure that the rim is not any higher than 34 inches higher than the floor. Aside from that, the sinks should extend out a minimum of 17 inches from your rear wall, along with the area under the sink have to be opened with a clearance for at least 29 inches beginning with the floor to the bottom from the sink. If in case you desire your sink to become installed in a countertop, consider putting n't i more than 2 inches through the side of the counter. According to some experts, this promotes maximum accessibility. Additionally, you can employ a protective boot within the water lines and trap underneath the sink to prevent contact. Utilize a single-handle, lever-style faucet that is easily operated with one closed fist.

Floor Covering

Many homeowners considered the sheet vinyl floors as the best choice. The primary reason for this could be its smooth quality as well as being easy to clean. However, if you are using a ceramic tile, try to choose large and smooth tiles in order to lessen the grout lines plus some surface irregularities. Also locate a non-slip surface texture. And, if you are floor carpeting, stick with naps that are ½ inch high or less.

Interior Clearances

This is another advice if you are wheelchaired. Well, for you to make a 180-degree turn, a wheelchair needs no less than 60 inches, that's 5 feet, of clearance. Note that this amount of clear space is oftentimes tough to achieve, but think about a T-shaped space instead. Both sides of the T has to be at least 36 inches wide. As outlined by some experts this configuration enables space for a wheelchair in order to comfortably make a three-point turn rather than having to maneuver in a complete circle. Additionally consideration, try to make pathways to the fixtures at least 36 inches wide. And, when it comes to the sink, it must have a clear space facing it.

Grab Bars

Perhaps one of several wonderful features in just about any bathroom is the grab bars. These even result in the bathroom safer plus more convenient for anyone to use. Well, it is important to note that if you are installing a horizontal grab bar, it needs to be positioned on the wall behind stained. You can install one more on the closet sidewall adjacent to the toilet. Also, the grab bars must be placed inside bathtub in addition to shower enclosures. If you are remodeling or installing new as well as the walls in the room are open, make sure you provide wood blocking within the walls. This will allow simplification from the grab bars' attachment.
Okay, enough about those guidelines. Let's now proceed to some steps to put in your shower or bathtub.

How to Install Shower and Bathtub

When thinking for installing a bath or bathtub, it is very important to note that the pipes required add the hot as well as cold supply lines, other than a pipe ultimately causing a shower head. Also, most pros often suggest a blending valve and shower head for the installation, including air chambers.

Usually, the tub or shower fixtures rate lower in fixture units. In order that they are often placed on the branch drains and wet or back vented just like the sinks. Accordingly, the two shower stalls and tubs type in the stack at floor level or below as a result of angle of which a floor drain trap is defined.

When it comes to faucet and shower head assembly, one should be aware that it requires an open wall for installation. Also merit consideration is that, bathtubs and shower stalls might need support framing. Among the common ideas here's that a bathtub filled with water is extremely heavy; therefore, you will need to examine first the building codes, including the framing support prior to bathtub installation. Additionally there is a required floor position for a shower stall. In accordance with some experts, a nominal amount area required is 1,024 square inches, however you should also allow 24 inches from the stall itself on a vacation fixture or wall.

Allow me to share the basic guidelines:

1. All piping should be installed before installing the bathtub itself.

2. Lower the bathtub into place. This will allow a nonstop flange to fit against the wall studs and rests on 1 x 4 or 2 x 4 supports. In terms of this, don't forget to anchor the bathtub to the enclosure with nails or screws ensconced over the flanges into the studs.

3. Put together the drain connections. You can do this by way of attaching the bathtub overflow with the tub drain over the trap, and not beyond it. Observe that the trap may compression fitting that screw in the arm of the overflow assembly.

4. Run the hot and cold water lines on the tub or shower mixing valve where they are attached. You can do this by sweating these into the hot and cold ports with the mixing valve.

5. Run a pipe up the wall to the shower head. Note however that on top of this pipe, you should sweat on a brass female threaded winged fitting that's nailed or screwed into a framing support.

6. Some 1/2" pipe should be extended, but this must be in accordance on the instructions provided by producer, for the tub spout. Also sweat over a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and also a 1/2" cap.

7. At the moment, you will need to have your rough plumbing checked.

8. Restore water pressure and inspect the drain connection, such as supply pipes for any leaks.

9. Replace the wall with moisture resistant drywall as a base for your wall covering. Equally important to note is to seal joints involving the wall and your new tub perhaps with silicone caulk. This caulk will serve as protection against water seepage.

10. It is now time to install the handles, shower head and Spout. Note that the shower head screws onto the shower arm stub out. And, if you are installing a new polished brass shower head or replacing a well used one, always clean the pipe threads and apply a new pipe joint compound. You can even consider a Teflon tape or both to stop leaks.

Installing a Bathtub Surround

As you may know, a bath surround (commonly known as wall kit) is a straightforward way to provide a handsome, watertight and easy-to-maintain barrier around a tub or shower alcove. These surrounds can be put up over plaster, tile, drywall or any solid and flat wall. Well, there some surround kits out there these days. Most kits contain either three or five pieces that overlap to are the cause of different dimensions. Also, these kits include instructions, that you just should consider reading prior to leaving the store. When installing a tub surround, you may require a glue as well as color-matched caulk, so consider buying these in the store.

Installing a tub Enclosure

Bathtub enclosures initially are a necessary completion to a drop-in tub or a whirlpool tub. So, if you are considering any of those kinds of tub, then consider installing an enclosure.

Installing a bath enclosure is actually not as difficult as it looks. You'll be able to build it even with a little skill and of course with the right materials. Consider the following:

Sizes and types

One of the most important considerations in terms of building a bathtub enclosure will be the type of the tub. In particular, the drop-in bathtubs that are made specifically for bathtub enclosures have been proved to be the best to build around. But, the whirlpool bathtubs will also be great for building enclosures around.

An enclosure is basically necessary to hide water pipes on both the drop-in and whirlpool tubs. So, it is vital that when you consider building one, make sure to work around the plumbing and also the draining systems to stop interfering with pipes.


Comments

There isn't any comment in this page yet!

Do you want to be the first commenter?


New Comment

Full Name:
E-Mail Address:
Your website (if exists):
Your Comment:
Security code: